Where to find IH 2000 loader spare parts? - Yesterday's Tractors
May 11, 2019 · The return oil from the loader system comes out of the right hand hard line on item 1 in that figure. Item 7 bolts to the bottom of the lift housing with a gasket sealing in the oil needed for the lift cylinder. The stand tube shown on the left hand side of item 7 in the figure sets the oil level in the lift housing.
IH 444 Fluids Questions | Yesterday's Tractors Forums
Jul 18, 2018. #1. Hey Everyone. As you may have read previously, I have a "new to me" IH 444 with a 1501 Loader. I finally got her home, and was actually able to read the S/N under the layer of grease. I have #2248, a 1968. Anyways, I'm gathering up everything to get her serviced and ready for use here. My intentions are to drain everything and ...
12V Conversion on IH Utilitty 340 | Yesterday's Tractors Forums
New User. Jun 4, 2009. #1. I have a '63-ish IH Utility 340 with the C135 engine, and I have determined to convert it to 12V. I've already replaced just about every electrical component in the tractor with 12V negative ground appropriate versions, but one crucial component remains--the generator. I would really like to get a one-wire alternator ...
IH 2444 oil filter and governor questions - Yesterday's Tractors
Jun 23, 2023 · Well-known Member. receives it oil from the reservoir tank on the loader frame. Depending on the age of your 2444 it may have 80/90 wt gear oil in the trans/diff. The lever is checked by a pipe plug, IIRC the plug was on the right side of trans case by foot rest by brake pedal. If it is not there then it is on the.
IH 284 3 pt set up | Yesterday's Tractors Forums
Jun 28, 2016. #1. the 3 pt systems i'm familiar with lift with the 2 lower arms & the 3rd upper link is a leveling adjustment. this lifts from 2 upper arms. the woods mower is lifted via the arms which are hooked to chains. a set of lower arms did come with the tractor but these also would just go along for the ride. the lifting would still be ...
IH 684 Loader Plumbing | Yesterday's Tractors Forums
New User. Feb 14, 2024. #16. Hi All, I am going through the same process as the op plumbing loader onto my IH 684 tractor. I have done as suggested above by taking out the power beyond plug and plumbing from it to the side marked "in" on the loader valve bank and then plumbed the outlet down into the hole below the axle.
McCormick / IH 80 Parts | Yesterday's Tractors Forums
Sep 4, 2009 · Member. Sep 7, 2009. #1. in the model 80 parts book the unloading auger belt part number is 13 988K for the 540 rpm or 935 721 R1 for the 1000 rpm. hope this helps it don"t list the length. 1.
Plow parts for IH LIttle Wonder | Yesterday's Tractors Forums
Sep 30, 2024 · Oct 1, 2024. #3. Tom Elliott said: Looking for shares and landside for a IH Little Wonder 12" two bottom. Need two shares #0-552 and the front landside #0-2018. Even if these numbers mean anything anymore. I found this Little Wonder and trying to make a usable plow out of it. Got everything freed up and working.
IH 444 pto disengaging | Yesterday's Tractors Forums
Oct 14, 2024 · The photo is of an IH Bradford, UK completely built tractor. I live in Canada and we only received the B250, B275, B414, 434, 444 and 384 series of tractors completely built in IH plant Bradford, UK and shipped to Montreal, Quebec or IH Hamilton, Ontario. My Dad had B414, 434 and later 384, all build in IH plant, Bradford, UK.
1976 IH Hydro 100 prototype tractor - Yesterday's Tractors
Oct 15, 2024. #1. I'm a writer for Antique Power magazine and researching the IH Hydro 100 prototype that was built around 1976 at a dealership in New Ulm, MN. The tractor still exists even though it was built as a prototype and is owned by a collector in Illinois. The story is Brown County Implement in New Ulm had six stripped down Hydro 100s ...